Shopping Cart
Your Cart is Empty
Quantity:
Subtotal
Taxes
Shipping
Total
There was an error with PayPalClick here to try again
CelebrateThank you for your business!You should be receiving an order confirmation from Paypal shortly.Exit Shopping Cart

Multipure Water Filtration Systems

Multipure Independent Distributor

I.D. # 424948

Carole Allen

386 437 7019

This is a wonderful article by a fellow distributor






How to Choose a Water Filter:  by a fellow Multiure distributor

Is it important to choose a filter that is certified? How to know which contaminants a filter removes and how much.

pitcher?  carbon block?  reverse osmosis? whole house? certified? nsf/ansi standards 42, 53, 58, 401?  

A survey by NSF International found 82% of Americans are concerned about the quality of their tap water. This survey predated the water crisis in Flint, Michigan.  Frankly, none of us knows what is in our tap water.  You want to remove contaminants from your water, but are not sure how to select a water filter.  It is quite simple. There are three key concepts:
  • NSF/ANSI water treatment standards;
  • Certification to those standards, and
  • Performance Data Sheets
If you do not want the detail I provide below, the bottom line is that you want a solid carbon block filter certified to NSF/ANSI 42, 53 and 401(and 58, if you would like to add reverse osmosis), and you must review the manufacturer's Performance Data Sheet to know which contaminants any particular filter reduces. Performance varies widely between filters carrying the same certification (read more below). My research led me to choose Multipure filters.  I use Multipure's Aquaversa model which is certified to Standards 42, 53 and 401.  Consumer Reports ranked Multipure's Aquaversa as its top under-the-sink water filter in the March 2017 issue. See Multipure's Performance Data Sheets here, including Aquaversa's.  Compare its cost, Performance Data Sheet and warranty to other filters you are considering.  By the way, Multipure's filters reduce the lead in water to safe levels, removing more than 99.3%. Note no certified reduction claim is valid when dealing with water as contaminated as Flint's, though.
When comparing the cost of water filters, also consider the number of replacement filters and the gallons of water each filter will process before needing to be replaced.  Frequent filter changes will get you in the long run.
After a lot of research, I chose Multipure filters. I offer them to you through this website, because they are the best I could find.  I offer what I use.  
If you have a question, please feel free to call me at (800) 294-1349 or email me [email protected] I will not bother you with any follow up phone calls or emails or even try to sell you a water filter.  I simply share information.  I respect your privacy and busy life.  
In case you are interested in contaminants commonly found in tap and bottled water that are especially dangerous to pregnant women and young children, check them out here. Actually they are dangerous to us all.  
CERTIFICATION:  Consider only certified treatment systems or filters.  If certified, manufacturers are required to provide a Performance Data Sheet, listing contaminants reduced.  If a water filter or treatment system is not certified, you can only guess which contaminants it might reduce. Those manufacturers that choose certification will have the filter certified to the appropriate NSF/ANSI standard.  The three certifying organizations are NSF International, WQA (Water Quality Association) and UL (Underwriters Laboratories).  See more on certification below.
STANDARDS:  The standards to which water filters are certified are developed and published by NSF International and American National Standards Institute (NSF/ANSI). Four residential water treatment standards are described below. Water filters are certified to these standards. Certification (e.g., to NSF/ANSI Standard 53) means the filter has met at least some of the requirements described in that water filtration standard. "At least some" is a problem that is discussed below.  
YOUR BASIC CHOICES:   
NSF/ANSI 42: Drinking Water Treatment Units - Aesthetic Effects. Filters certified to this standard reduce specific aesthetic or non-health related contaminants (chlorine taste and odor and particulates).  These filters basically make your water more palatable.
Product examples:  The most common products certified only to this standard are water pitcher filters and refrigerator filters.
Multipure does not offer filters that are only certified to this standard.  
NSF/ANSI 53:  Drinking Water Treatment Units - Health Effects (also includes NSF/ANSI 42 certification).  Filters certified to this standard reduce specific health-related contaminants.These filters use carbon filtration. The quality of the carbon filter determines which contaminants are reduced and to what extent.  For that reason, filters certified to Standard 53 vary widely in their ability to remove contaminants.  You must consult a filter's Performance Data Sheet to learn which particular contaminants are reduced. Examples include Cryptosporidium, Giardia, some heavy metals (e.g., lead, pentavalent arsenic, mercury), pesticides, herbicides, benzene, MTBE, radon, trihalomethanes and PCBs.  It can be used in conjuction with reverse osmosis technology (certified under Standard 58) to remove additional contaminants.
Product examples: These filters are typically installed below the sink.  Some products may have two or three filters; others may have a single, more powerful solid carbon block filter. Some faucet-mount filters are certified to Standard 53, although they are unable to compete performance-wise with a larger solid carbon block filter.
Multipure's Aquaversa, Aquadome and Aquaperform filters are certified to NSF/ANSI 53. They are available for under-the-sink, countertop or inline use for a refrigerator.  See product descriptions here and Multipure Performance Data Sheets here
NSF/ANSI 401: Emerging Compounds/Incidental Contaminants.  This is a new standard that was developed in reaction to the public's concern over pharmaceuticals being found in our tap water.  Filters can be certified to reduce up to 15 contaminants, including over-the-counter and prescription drugs. Other contaminants included are new types of herbicides and pesticides, chemicals used as flame retardants and detergents. 
Product examples:  The most common product certified to this standard is a carbon filter that would be used under the sink, on the countertop or inline for a refrigerator.
Multipure's Aquaversa and Aquadome are certified to reduce all 15 contaminants. covered under NSF/ANSI Standard 401. They are available for under-the-sink, countertop or inline use for a refrigerator.  See product descriptions here and Multipure Performance Data Sheets here
NSF/ANSI 58: Reverse Osmosis Drinking Water Treatment Systems.  Certified reverse osmosis systems are able to reduce some of the same, but also entirely different contaminants than carbon filtration.  Likewise, carbon filters can reduce contaminants that a reverse osmosis system cannot. For that reason, reverse osmosis systems include carbon filters. Reverse osmosis systems are able remove perchlorate, fluoride, nitrate, nitrite, radium, and heavy metals such as hexavalent and trivalent chromium, cadmium, copper lead and mercury
Reverse osmosis systems should include pre-filters and a post-filter along with the reverse osmosis membrane.  The performance of this system is dependent upon the quality of the pre-filters and post-filter as well as the RO membrane.  Like carbon filters certified under Standard 53, RO systems vary widely in their ability to reduce contaminants.  You must consult the Performance Data Sheet. If the percentages of contaminants reduced are not listed, assume it is the minimum to pass certification.
Multipure's reverse osmosis, AquaRO, system uses three pre-filters.  Multipure's Aquaversa filter is used as the post-filter. See the product description here and Multipure Performance Data Sheets here
HOURS OF SEARCHING, A UCLA INTERLIBRARY LOAN, BUT STILL WITHOUT CLARITY!
In my quest to understand what “certification” to a certain standard meant, I asked my public library if they could locate a copy of NSF/ANSI Standard 53.  It's not a very popular publication. They had to secure a copy from UCLA through an inter-library loan (it cost me $20 because it was out of state, but it was well worth it).  This standard, NSF/ANSI 53, goes into 118 pages of detail, including requirements for filter materials, structural performance, minimum performance requirements, elective performance claims and performance data sheet requirements. Many filters claim "NSF/ANSI 53" certification. All I wanted to know was what a filter certified to NSF/ANSI 53 removed and how much.  Unfortunately, that information was not provided in the standard itself.  It was at this point that I decided to call NSF.  By the way, NSF not only develops and publishes the residential water treatment standards along with ANSI, they also certify water filters.  I should add that there are two other organizations that certify products to the above standards – WQA (Water Quality Association) and UL (Underwriters Laboratories).

NSF EXPLAINS WHAT “CERTIFICATION” MEANS 

I spoke at length with a very knowledgeable and forthcoming NSF representative.  I would describe that conversation as “eye opening”.  It might be better classified as an “are you kidding me!”conversation.  This is what I learned:
If you select a water filtration system that is certified to one of the NSF/ANSI standards listed above, you will have the following assurances:
  • The system is structurally sound;
  • The system does not add anything harmful to the water;
  • Advertising, literature and labeling are not misleading;
  • The materials and production processes don’t change, giving you consistent product quality over time; 
  • Contaminant reduction claims made by the manufacturer are true. These claims are to be disclosed in a “Performance Data Sheet”.  
“Are you kidding me!” refers to the last bullet point.  Two different water filters can carry the same certification, from the same certifying organization (i.e., NSF, WQA or UL), yet be certified to reduce different contaminants and different amounts of those contaminants.  Please read the information I share below. You can’t properly select a water filter unless you know this information.  It may prevent you from buying a water filter that does not reduce the contaminants you thought it did. 
    CERTIFICATIONS ALONE DO NOT TELL YOU WHICH CONTAMINANTS ARE REDUCED

CERTIFICATIONS ALONE DO NOT TELL YOU WHICH CONTAMINANTS ARE REDUCED
Again, what I learned from this NSF representative is you could have several filters that carried the same certification (NSF/ANSI 53, for example) with incredibly different performance. Their contaminant reduction claims could range from one contaminant to the most contaminants of any, at the highest percentages, of any filter on the market. I clarified my understanding with the NSF representative twice – a filter with one contaminant reduction claim could carry the same NSF/ANSI 53 (or other) certification as a filter that was certified to reduce the most contaminants of any on the market.  Yes, that is correct. Doesn't that make your jaw drop? No wonder so many people purchase the faucet-mount or water filter pitchers! They may have the same certification, but simply cannot compete with the larger, high-quality solid carbon block under-sink or countertop filters. See the five bullet points above.  Certification may only apply to the top four because the manufacturer may not have made any contaminant reduction claims.  Yet the best and the worst will have the same stamp on their product.
                    CERTIFICATION SYMBOLS SHOULD CARRY A WARNING:  SEE MANUFACTURER'S                                 PERFORMANCE DATA SHEET FOR A LIST OF CONTAMINANTS REDUCED
CERTIFICATION SYMBOLS SHOULD CARRY A WARNING:  
SEE MANUFACTURER'S                           PERFORMANCE DATA SHEET FOR A LIST OF CONTAMINANTS REDUCED

 

WHICH CONTAMINANTS DOES YOUR FILTER REDUCE AND HOW MUCH?   IT’S ALL ABOUT THE PERFORMANCE DATA SHEET!

The NSF representative did stress that if any contaminant reduction claims were made, the top four bullet points had also been met. Regarding the fifth bullet point above, manufacturer contaminant reduction claims, you must consult the manufacturer’s "Performance Data Sheet” to understand the contaminant reduction claims for any particular filter. The manufacturer is required to publish this information if a filter is certified.  Unfortunately, although the contaminants reduced are listed, the percent removed is not always provided.  There are minimum reduction requirements for each contaminant certified under an NSF/ANSI standard. However, a filter can be certified to remove a much higher percentage and even more contaminants than the minimum required under a given NSF/ANSI standard.  

SEE A MODEL PERFORMANCE DATA SHEET!

As I searched for the filter that I wanted for myself, I found that Multipure’s Performance Data Sheets provided both the contaminants reduced and percentages of those contaminants that the filter is certified to remove. Multipure's filters were consistently the best I found.  I can't tell you how many filters/Performance Data Sheets I reviewed, but I spent hours comparing them on an Excel spreadsheet. I chose Multipure filters for my family. The choice was straight forward.
Click here to see Multipure's Performance Data Sheets for their solid carbon block filters, certified to NSF/ANSI 42, 53 and 401, and for the reverse osmosis system certified to NSF/ANSI 58.
I haven’t scoured the internet looking for this level of disclosure from other manufacturers, but I rarely ran across the level of detail Multipure provides.  If the percentages of contaminants removed are not listed, I assume it’s just the minimum amount required for certification.  If they are listed, compare them to Multipure filters. This is one of the many reasons I choose to use Multipure filters, and eventually decided to offer them to you and pass this information on to the most vulnerable of water consumers – pregnant women (and their fetuses), infants, children and those with fertility issues.
 

Share












COMMENTS (16)

Newest First 
Preview POST COMMENT…
  
Hi there, not sure if you will respond but i'll give it a try. I've purchased a water filter (more like a machine called Leveluk R that produces Kangen Water at different ph levels ranging from 8.5-9.5 and also Clean Water free from most of the harmful chemicals) from Enagic 3 years ago and never really knew how big of a role certifications play when purchasing a filter. Recently I searched through their website to see what certifications they have and found out that they are NSF/ANSI 42 and NSF/ANSI 372 and 61 certified. After reading through your post I noticed that they meet the standards of certification, however I am concerned about how it doesn't remove harmful viruses or bacteria and also some other chemicals. Since Multipure has a filter system called Aqualuxe do you think I should sell my machine and purchase the Aqualuxe drinking water system?
  
You should look at Amway’s eSpring w/ UV.
  
Thanks, Mike. I will check it out.
  
Posted that before fully looking through your website...realizing you are not hiding this...sorry. Jaded from fake articles on the internet meant to sell items.
  
No problem, Steven! I chose Multipure filters for myself after a thorough review of certified filters. I enthusiastically offer them to those looking for clean water. The Aquaversa, which I use, was selected as the best under-the-sink filter by Consumer Reports in their March 2017 edition.
  
Does Multipure pay you in any way? You offer filters to customers who visit your website?
  
Hi Karen,
Thank you for a very educational blog post.
I've spent some time studying water filters -- but obviously not enough, because I was not aware that a filter mfr could claim NSF 53 certification if their filter reduces just onecontaminant. I assumed that NSF 53 certification meant that the filter reduced all listed contaminants by at least the minimum amount.
I have looked at performance data sheets, and have never seen any that only listed one or two contaminants, but that sure is good to know to it's a possibility. I will be going by the data sheets from now on.
I've been using the Pentek P-250A 2 filter set. They have decent specs, but I will compare them with Multipure.
Sherman
  
Hi Sherman,
Thanks for your interest and comment. I looked at the filter you have been using. Although it is certified to NSF standards 42 and 53, it reduces far fewer contaminants than Multipure's products. I like the solid carbon block filter technology Multipure uses (they also developed this technology). I am guessing yours is granular activated carbon. I am no expert, but you can read more at http://www.multipure.com/mpscience/carbon-block-filters/. Still, it looks like for the price it does a decent job with certain contaminants.
Thanks again for you comment, Sherman!
Karen
  
nice post, very helpful read the blog, i also mumbai city Best Multi-pure Water Filter Residential Commercial Under Sink Systems Machine From Supplier http://www.aquatechindia.com/
  
Hi Karen,
Following up, and it does look like the system you recommend is one of the best out there. I was looking and didn't see a UV attachment available. But I might have missed it. Do you know anything about whether it's possible to add one, if they offer one? That will take care of the bacteria and viruses, it apparently wrecks their DNA.
  
Hi Lila,
Multipure's newest filter, the Aqualuxe, addresses your concerns. It is certified to "reduce" (certification claims cannot state, "removes") bacteria and viruses. The NSF certification is to Standard P231. Filters certified to this standard are classified as "microbiological water purifiers". Last time I checked, the Aqualuxe was listed as just one of two filters certified to this standard on NSF's website. Check out this filter at http://www.multipure.com/aqualuxe/.
Again, I defer to the Multipure staff on detailed technical questions. They do this full time! I chose Multipure for myself and offer Multipure filters to customers who visit my website, but they are the experts (which is one reason why I chose them). If you have more questions, I suggest you call them and ask to your hearts content. They are a family-owned company that treats customers like family. If you would like to call, Multipure's number is 800-622-9206. Again, I am not trying to push you off. Please feel free to ask me whatever you'd like. I just know they can answer any question you might have.
Thanks for your continued interest!
Karen
  
Karen,
Did you realize that the AquaPure doesn't purify for Bacteria or Viruses? That's a requirement for me. Their data sheet states their filter is at 0.5 microns (nomimal, which means on average. Absolute-means no pores larger than, absolutely) Pathogens like Cholera, E. Coli, and Salmonella are (0.2 – 0.5 microns) and viruses such as Hepatitis A, rotovirus and Norwalk virus (.004 microns). So, these buggers will flow right through, along with any others less than 0.5 microns.
Still searching then......
  
Hi Lila,
I certainly appreciate your concerns (really!) and may have a solution for you. Just to clarify, the filter I use and filters I endorse (and sell) are Multipure, not AquaPure. Multipure has a new filter (Aqualuxe) which is certified to NSF Standard P231. Filters certified to this standard are classified as "microbiological water purifiers". The Aqualuxe is listed as just one of two filters certified to this standard on NSF's website. These filters reduce (claims cannot state, "removes") bacteria and viruses. I have not yet added this filter to my product list on my website (waterformoms.com), but need to do so! Let me consult Multipure for more specifics on the bacteria and viruses addressed. They are the experts that I can consult. I will get back to you.
Best Regards,
Karen
  
I too was considering one of the Berkey Systems. They claim to "meet" NSF certification. Which isn't the same as being NSF certified. Although they used to have their results posted on their website. I called them and asked, "If you went through the process of testing to see if you met the standards, why not get the certification?" The person on the phone had no answer. So, after seeing many people also complaining that Berkeys have leak problems. I didn't buy. I'm still searching. Thanks for the great explanations Karen...!
  
What about the Big Berkey? It isn't certified, but is supposedly an excellent filter system recommended by many. Any thoughts on this?
0